With the UVS-1 you can cut metals + plastics. From cardboard tubes (6 mm), gasket material, cardboard corner protectors and hard floor coverings e.g. in buses to thin sheet iron. The track scissors with its double-sided cutting system can cut very short curves – left or right – and achieve a minimum inner radius of 30 mm in plastic or 50 mm in metal (depending on the material).

Knives and jaws (side knives) can be reground.

Optional accessories are line cutters for cutting parallel strips up to 100, 250 or 500 mm.

Line cutter S/01 for metal and S/02 for plastics.

 

Draco Universal Shears UVS-1

up to 2.0 mm steel

The SD7-1 is a very manoeuvrable shear and can make short turns (smallest inner radius 50 mm).
This is therefore the ideal schear for zinc processors, interior construction, body shops, garage companies and damage repair!

For example, perfect for the installation of sunroofs or in the ceiling construction for the installation of spotlights.

Knives and jaws can be reground. These light, compact and robust schears are used both in assembly and in mass production by means of linear guide systems can be used.

Universal Slitting Shears SD7-1

This powerful shear is ideal for cutting U-, C-, O- and L-profiles, machine covers, angles and plate up to 2 mm and is particularly suitable for construction companies, ductwork, switch cabinet construction etc., anywhere where a higher capacity is desirable.

Knives and jaws (side knives) can be reground.

This robust shear is in the assembly as well as in the mass production by means of linear guide systems can be used. The hole with adjusting screw for the mounting is already present. The assembly in the vise is made possible by means of flat sides on the shear’s head.

As optional accessories, strip cutters S/01 are available for cutting parallel strips up to 100, 250 or 500 mm.

 

Metal Slitting Shears 1020-1

Universal powerful shears for sheet metal up to 1.6 mm and therefore particularly suitable for installation companies, assembly and craft. Ideal also in the reduction for cutting metal stud profiles.

For cutting UA profiles up to 2 mm see type 3515.

Knives and side knives can be reground.

These light, compact and robust scissors are used both in assembly and in mass production by means of linear guide systems can be used.

Optional accessories are line cutters for cutting parallel strips up to 100, 250 or 500 mm.

Metal Shear 1610-1

up to 1.3 mm of steel

Ideal shears for installation, air conditioning, ducting, aircraft manufacturing companies.

Cutting air ducts, sandwich board, making a cold bridge and a thousand and one other applications. Also ideal for cutting U-, C-, L-, and metal stud profiles (for reinforcement profiles see type 3515)

Knives and side knives can be reground. These light, compact and robust shears are used both in assembly and in mass production by means of linear guide systems can be used.

Metal Slitting Shears S1001N-1

Very manoeuvrable schear that can make short turns (smallest inner radius 50 mm). Ideal for car plate and zinc work up to 1.0 mm.

Particularly suitable for body shops, garage companies, car body repair and interior construction.

For example, perfect for the installation of sunroofs or in the ceiling construction for the installation of spotlights.

Knives and side knives can be reground.

These light, compact and robust shears are used both in assembly and in mass production by means of linear guide systems can be used.

Optional accessories are line cutters for cutting parallel strips up to 100, 250 or 500 mm.

Draco Pneumatic Metal Shears 1910

Universal pneumatic metal shears for various applications. Cut up to 1.3 mm of steel.

Cutting air ducts, sandwich board, making a cold bridge and a thousand and one other applications. Also ideal for cutting U-, C-, L-profiles. Knives and side knives can be reground.

These light, compact and robust shear is used both in assembly and in mass production by means of linear guide systems can be used.

Optional accessories are line cutters for cutting parallel strips up to 100, 250 or 500 mm.

Draco Pneumatic Metal Sheer 1913

This powerful shear is ideal for cutting e.g. U-, C-, O- and L-profiles, machine covers, angles and plate up to 2 mm and is particularly suitable for construction companies, ductwork, switch cabinet construction etc., so wherever a higher capacity is desirable.

Knives and jaws (side knives) can be reground.

This robust shear is in the assembly as well as in the mass production by means of linear guide systems can be used. The hole with adjusting screw already present. The assembly in the vise is made possible by means of flat sides on the shear head.

As optional accessories, strip cutters series S/01 are available for cutting parallel strips up to 100, 250 or 500 mm

Draco Pneumatic Metal Shears 1920

especially for plastics

Ideal for use in interior design, decor construction, window dressing, trade fair construction, aircraft construction, body construction, acoustics, joineries and much more.

Splinter-free cutting of all plastic sheets such as Pk-tex, Textolite, Formica, Perstorp, Ultrapas, Resopal, Celamin, Hornitex, Getalit, Novatex, Thermopal, Tacon etc. **

Fiber-free and low-dust cutting of hardboard, Pavatex, Renovite, cardboard, Masonit, Silvacolor, Hornitex, Glasal etc. **

In addition, cold cutting of Inlaid, linoleum, veneer, Deliflex, Mipolam, PVC, glass fiber reinforced polyester (low dust!) etc. **

** NO PLEXIGLAS! **

Draco Pneumatic Plastic Shears 1950

Draco Plastic Shear 3550, 500 Watts.

Splinter-free cutting of many plastic plates such. Pk-Tex, Textolite, Formica, Perstorp, Ultrapas, esopal, Celamin, Hornitex, Getalit, Novatex. Thermopal, Tacon, etc. **

Fiber-free and low-dust cutting of hardboards, Pavatex, Renovite, cardboard, Masonit, Silvacolor, Hornitex, Glasal, etc. **

In addition, cold cutting of inlaid, linoleum, veneer, etc., Deliflex, linoleum, Mipolam, PVC, glass fiber reinforced polyester (dust-free!), Etc. **

NO PLEXIGLAS *

Draco Plastic Shear 3550

Profile shear with large blade opening, ideal for cutting over thickening of the material. Up to 2.0 mm steel (eg ribs in cable ducts and overlaps), U-, C- and L-profiles and spark-free cutting for use in explosion hazardous areas.

The universal cutting device for the electrical installation, recycling, appliance and switch cabinet construction.

Super-fast cutting, shortening or trimming of cable trays, switch boxes, metal-stud profiles, steel profiles, cover caps, spiral- and seam-folded tube.

Draco Pneumatic Metal Shear 19/3520

Profile shear with large blade opening, ideal for cutting over thickening of the material. Up to 2.0 mm steel (eg ribs in cable ducts and overlaps), U-, C- and L-profiles and spark-free cutting for use in explosion hazardous areas.

The universal cutting device for the electrical installation, recycling, appliance and switch cabinet construction.

Super-fast cutting, shortening or trimming of cable trays, switch boxes, metal-stud profiles, steel profiles, cover caps, spiral- and seam-folded tube.

Draco Radius-Seam Metal Shear 19/3514-7R

up to 2.0 mm sheet steel

The universal cutting device for the electrical installer, apparatus and control cabinet construction. The solution for cutting cable trays, cable tray lids, cable ladders, trapezoidal profile rungs, cable protection channels, stiffening UA profiles, wide span beams, cassettes, panels etc. The profile shears effortlessly cuts across angles and profiles.

The cutter works without sparks (saves the dangerous work with the angle grinder) and can therefore also be used in the building. No deformation of the profile and no burr formation.

Draco Profile Metal Shear 3520

up to 1.3 mm sheet steel, crosswise and angle cut of corrugated materials

cuts all materials that can be punched, such as mild steel, stainless steel, aluminum, non ferrous metals and plastics Optimum ease of use, excellent

Draco 1213-1 Corrugated Nibbler

Profile nibbler with a foot that is adjustable at 45 ° steps, making it ideal for profiles such as sheet piles and roof plates up to 1.6 mm. Central switch ideal also for left-handed people.

For trimming roof profiles up to 160 mm tread depth, the 1216-1 can be equipped with the profile set 160 (Item No. 12160005).

Draco 1216-1 Corrugated-Electric Nibbler

up to 1.0 mm sheet metal

Agile shear, handy for tight radii (50 mm) and therefore ideal for roof plumbers, interior fittings (for example, ceiling construction – installation of spots) and motor vehicle workshops (for example, when installing sun roofs).

Knives and jaws can be reground. These robust schears are used both in assembly and in mass production by means of linear guide systems can be used.

5-piece 12 volt professional set AK 3010 Ni-MH consists of:
1 cordless shear AK 3010,
2 batteries MXL12,
1 charger RC and
1 transportbox.

Cordless Metal Shear 3010 Ni-MH

This cordless shear is ideal for cutting and cut outs of sheet metal as well as U, C and L profiles. Cuts burr-free and without deformation. A universal sheet metal working device. Ideal shears for installation, air conditioning, ducting, aircraft manufacturing companies.

Cordless Metal Shear AK 3013 Ni-MH

up to 1.6 mm sheet metal 

Ideal for cutting, cut-outs and trimming of all kind of sheets as well as U-,C and L profiles. Universal sheer processing device.

 

 

Cordless Metal Shear AK 3016 Ni-MH

up to 2.0 mm, or 4×0.75 mm steel

Cold cutting without flying sparks! Ideal for cutting recesses in sprial ducts and sheets of all kind. Cuts straight and tight radii ( min. 45 mm ) in sheets and even over seams

Ideal for air and climate technology, installation companies, truck workshops, metalworking companies, etc.

Cordless Radius Seam Metal Shear AK 3514-7R Ni-MH

Up to 2.0 mm, or 4×0.9 mm steal, or 6×0.75 mm light metal

Cold cutting without flying sparks!

This shear is ideal for cutting spiral ducts, roof seams, cross seams, ridge seams and folds of sheet iron, aluminum, lead, copper, zinc or stainless steel. Cuts roller shutter boxes, cover caps, grid and wire in cage- and aviary construction ( flush-edged!)

Cordless Seam Metal Shear AK 3514-2 Ni-MH

up to 2.0 mm steel

The profile metal shear AK 3520 is perfectly adapted to the needs of the installation companies. It easily separates cable ducts, drywall profiles, but also spiral fold, flat sheets, U-, C- and L- profiles and much more.

Cordless Metal Shear AK 3520 Ni-MH